How to install an 5G click SPC floor?

Installing Stone Plastic Composite (SPC) flooring with a 5G click system offers a durable and straightforward flooring solution. The 5G click system simplifies the installation process through a fold-down mechanism, allowing planks to securely lock into place without adhesives. Here's a comprehensive guide to assist you:​ 

Preparation:

1. Prepare the Subfloor:

   • Ensure the subfloor is clean, dry, even, and free from debris.​

   • Level any uneven areas greater than 3 mm over a 1-meter span using a suitable leveling compound. ​lalegno.be+6cyberbox-product-medias.s3.ca-central-1.amazonaws.com+6interface.com.cn+6

   • Remove any existing floor coverings that are not compatible with SPC installation.​
     
     

2. Gather Necessary Tools:

• Utility knife​YouTube+10Home Depot Images+10Proper Floors+10

• Measuring tape​lalegno.be+31000grindu.lt+3Home Depot Images+3

• Spacers (5/16” or 8 mm)​lalegno.be+4Home Depot Images+4interface.com.cn+4

• Rubber mallet​Proper Floors

• Pull bar​materiaspc.com+7SAR Floors+7Proper Floors+7

• Tapping block​materiaspc.com+2SAR Floors+2lalegno.be+2

• Straight edge or square​Prodinex+4Proper Floors+41000grindu.lt+4

• Safety glasses​SAR Floors+161000grindu.lt+16Proper Floors+16

Installation Steps:

1. Plan the Layout:

   • Measure the room to determine the number of planks needed.​lalegno.be

   • Plan to install the planks parallel to the longest wall or the main light source for an optimal visual effect. ​materiaspc.com+1materiaspc.com+1

   • Ensure the first and last rows are at least half the width of a plank for structural integrity.​POCO Building Supplies+2Home Depot Images+2SAR Floors+2
     
     

2. Install the First Row:

• Place spacers along the starting wall to maintain a 5/16” (8 mm) expansion gap.​Home Depot Images+1SAR Floors+1

• Position the first plank with the tongue side facing the wall.​

• Align the next plank's short end at an angle of approximately 20-30 degrees to the previous plank's short end, then lower it to lock into place. ​materiaspc.com+1materiaspc.com+1

• Continue this process for the entire first row, ensuring all joints are tight.​Wood and Beyond+5materiaspc.com+5materiaspc.com+5
  
  

3. Install Subsequent Rows:

• Begin the second row with a plank cut to at least 30 cm in length to stagger the joints, enhancing the floor's stability and appearance. ​Prodinex+1SAR Floors+1

• Insert the long side of the plank at an angle into the previous row's groove, then lower it down.​

• For the short end, use a rubber mallet and tapping block to gently tap and lock the joint securely.​SAR Floors

• Repeat this process, ensuring a staggered pattern with at least a 20 cm offset between adjacent row joints.​
  
  

4. Cutting Planks:

• Measure and mark the plank where it needs to be cut.​

• Score the surface with a utility knife along a straight edge, then snap the plank along the scored line.​Home Depot Images

• Use the remaining piece to start the next row if it meets the minimum length requirement.​Prodinex
  
  

5. Final Rows and Finishing:

• For the last row, measure the width needed, accounting for the expansion gap, and cut the planks accordingly.​

• Use a pull bar to ensure the final row is securely locked in place.​SAR Floors

• Remove all spacers and install baseboards or moldings to cover the expansion gap, ensuring they are not fixed to the flooring to allow for movement.​
  
  

Post-Installation:

• Maintain room temperature around 25°C to prevent expansion or contraction issues.​ 

• Use felt pads under furniture legs to prevent scratches and place mats at entrances to reduce dirt and moisture on the floor.